D S P - 3 1 6 0 AVASTOR NO MORE PRODUCED Native| Translation ------+-----+-----+----- Form 3.5"/HH Cylinders 2599| | | Capacity form/unform 1600/ 2045 MB Heads 16| | | Seek time / track 9.7/ 1.0 ms Sector/track | | | Controller SCSI2 SI/FAST Precompensation Cache/Buffer 512 KB SEGMENTED Landing Zone Data transfer rate 3.000 MB/S int Bytes/Sector 512 10.000 MB/S ext SYNC Recording method RLL 1/7 operating | non-operating -------------+-------------- Supply voltage 5/12 V Temperature *C 5 55 | -40 66 Power: sleep W Humidity % 10 90 | 8 95 standby W Altitude km 2.500| 4.877 idle 11.5 W Shock g 10 | seek 12.9 W Rotation RPM 5403 read/write W Acoustic dBA 40 spin-up W ECC Bit 264 MTBF h 350000 Warranty Month Lift/Lock/Park YES Certificates CSA,FCC,TUV,UL1950,VDE ********************************************************************** L A Y O U T ********************************************************************** DEC DSP3160/3210 INSTALLATION GUIDE EK-RH2CA-IG.A01 50-pin SCSI Connector (8-bit) ----------------------------- +------------------------------------+ | Back View | | | +------------J1----------------J2----+ |+------------ ------------++-------+| ||oooooooooooooooooooooooo1||O O O O|| ||oooooooooooooooooooooooo2|| || |+-------------------------++-------+| +-----------SCSI-------------Power---+ + + +------------------------------------+ | Front View (Bezel End) | | | | Fault LED | +-+----------------------------------+ +-++----------+----------------------+ | ||ooo oooooo20 | + ||oooooooooo| + |+1---------J3 Option Busy LED Connetor +---------------------------------------------------------+ | Termination ++ |XX J1 | Header ++ |XX | |XX | |XX I | |XX N | |XX T | |XX E | |XX R | |XX F | |XX A | |XX C |+-+J3 Option |XX E || | Connector |1X || | | |+-+ |XX J2 |* Busy LED |XX Power +---------------------------------------------------------+ ********************************************************************** J U M P E R S ********************************************************************** DEC DSP3085/3105/3105D/3160/3210 INSTALLATION GUIDE EK-RH2CA-IG Jumper Setting ============== TERMPWR (Terminator Power) -------------------------- Generally, the host is the only device on the SCSI bus required to provide TERMPWR for the bus. To ensure that there is a sufficient level of power along the entire SCSI bus, Digital Equipment Corporation recommends that all devices on the SCSI bus supply TERMPWR (if they are capable). SCSI devices are protected by a diode or similar semiconductor to prevent back flow of the terminator power when more than one device supplies this power. TERMPWR ------- ++ | To provide TERMPWR, install the ++ | TERMPWR jumper at the following | ++ | locations. | ++ | | | | +-----------------------+------+ XXXX XXXXXXXXXXXXXXXXXXXXXXXXX SCSI Connector | +--------------------+ +--+ |xx| Drive provides TERMPWR to SCSI bus and active termination |oo| disabled. |oo| +--+ | +--+ |oo| Drive does not provide TERMPWR to SCSI bus and active |oo| termination enabled. |xx| +--+ | +--+ |xx| Drives provides TERMPWR to SCSI bus and active termination |oo| enabled. |xx| +--+ | +--+ |oo| Drive does not provide TERMPWR to SCSI bus and active |oo| termination disabled. |oo| +--+ SCSI Bus Termination -------------------- Both ends of the SCSI bus cable must be terminated. One end is terminated at the host. The other end must be terminated by the last SCSI device on the SCSI bus. Note Do not install Models DSP3105D (differential) or DSP3210WD (wide, differential) at the end of the bus. DSP3105D and DSP3210WD drives can not provide bus termination. SCSI ID (Address) Selection --------------------------- Each device on the SCSI bus must have a unique SCSI ID number assigned to it. The ID numbers for 8-bit SCSI drives range from 0 through 7. For 16-bit SCSI drives, the numbers range from 0 through 15. Configure the drive's SCSI ID at the Option connector by installing shunt jumpers across pins 1-2, 3-4, and 5-6. SCSI ID - 3085/3105/3105D/3160/3210 ----------------------------------- +----------+-----------------------+ +2--------20 | SCSI ID | Jumper Location | |ooo oooooo| Option | | PINS | |oooooooooo| Connector | | 5-6 | 3-4 | 1-2 | +1---------+ +----------+-------+-------+-------+ | 0 | OPEN | OPEN | OPEN | | 1 | OPEN | OPEN | CLOSED| | 2 | OPEN | CLOSED| OPEN | | 3 | OPEN | CLOSED| CLOSED| | 4 | CLOSED| OPEN | OPEN | | 5 | CLOSED| OPEN | CLOSED| | 6 | CLOSED| CLOSED| OPEN | | 7 | CLOSED| CLOSED| CLOSED| +----------+-------+-------+-------+ Configure Optional Features --------------------------- CAUTION The 5-volt signals of two or more drives should not be connected together or to any other current source by using the Option connector. Doing so may cause drive malfunction or component damage. Care must be taken when connecting the ground signals of two or more drives together to avoid ground loop problems. Ground loops may cause drive malfunction. The following optional features can be configured according to your system requirements. These features include: - Notification of AC power failure - Spindle synchronization - Write protection - Spin delay AC Failure Notification ----------------------- The host system (or power supply) can warn the drive of an impend- ing AC failure by asserting the signal AC_LOW L. This is an active low signal (low means power failure). NOTE The system should provide this warning at least 10 milliseconds prior to failure for this feature to be operational. To utilize this feature, connect the system's AC power warning signal to the referenced AC_LOW L pin on the Option connector. When the host system asserts the AC_LOW L warning to the drive, the drive prevents write-spliced for outstanding writes. AC_LOW L Connection ------------------- +---- LOGIC_GND L +-------+-20 |ooo ooo*oo|Option Connector |ooooooo*oo| +1------+--+ +---- AC_LOW L Spindle Synchronization ----------------------- DSP3000 Series drives support synchronized spindle operation. Master or slave synchronized operation is set through a SCSI Mode Select Page. When the drive operates as a Master, it generates a spindle synchronization reference signal (SPINDLE_SYNC_REF L). When operating as a slave, the drive synchronizes its spindle according to the SPINDLE_SYNC_REF L input reference. The drive always maintains local speed regulation when no reference signal is applied. NOTE The reference signal must originate from drives with the same electronics modules. Fo example, connect Model DSP3160 only with another DSP3160 drive. Do not connect the SPINDLE SYNC signal so that of any other model disk drive. Otherwise, the drive may mal- function. When connecting multiple drives together for spindle synchronization, be sure to use proper cabling techniques to avoid ground loop problems. Spindle Sync Connection ----------------------- The following figure shows the SPINDLE SYNC and associated ground connection pin on the Option connector. Option Connector +---------20 |*** @oooo*| * = LOGIC_GND L (Pins 2,4,6,20) |ooooooooo@| @ = SPINDLE_SYNC_REF L (Pins 10,19) +1---------+ For Models DSP3085/3105/3105D/3160/3210, pin 10 is provided as an alternate SPINDLE SYNC connection to facilitate installations where a 10-pin header is used to connect several remote features. Pin 19 is provided to facilitate the use of a 2-pin connector for SPINDLE SYNC connections. The ground return is pin 20, although pins 2, 4, or 6 can be used for the ground return. Write Protection ---------------- DSP3000 Series support either the Write Protect or Spin Delay mode. If your drive supports the Write Protect mode, install the jumper across the referenced pins of the Option connector. To disable Write Protection from 8-bit drives, remove the jumper from across 13 and 14 of the Option connector. Note that when the Write Protect Mode bit is set to a 1, automatic spin up occurs at power on. +---------20 |ooo ooXooo|Option Connector |ooooooXooo| +1---------+ Spin Delay ---------- DSP3000 Series drives support either the Write Protect or Spin Delay mode. If your drive supports the Spin Delay mode, you can program the drive automatically spin-up at powere on by installing the jumper across the referenced Option connector pins. To have spin-up controlled by a Start/Stop Unit command, remove the jumper. +---------20 |ooo ooXooo|Option Connector |ooooooXooo| +1---------+ Remote Features --------------- Remote features can be configured at the drive's Option connector to meet your system requirements. The remote features supported are: - Remote SCSI ID selection - Remote Busy and Fault display Remote SCSI ID Selection ------------------------ The Option connector enables you to set the drive's SCSI ID from an external (remote) switch or control panel. Configure the drive for remote ID selection by removing the SCSI ID jumpers (if present) from the SCSI ID pins. Then connect the leads from the external selection switch to the referenced pins. Observe the following guidelines while doing so. - ID bit 0, at Pin 1, is the Least Significant Bit. - SCSI ID bits 0, 1, 2, and 3 are active LOW signals. That is, the bit is a 1 if the corresponding remote switch is closed to ground. - For Models DSP3085/3105/3105D/3160/3210, use pins 2, 4, and 6 as the associated ground returns for ID bits 0, 1, and 2 respectively. They can be used individually, or the ground returns of all three ID bits can be combined at pin 2, 4, or 6. Option Connector +---------20 |*** oooooo| * = LOGIC_GND L (Pins 2,4,6) |@@@ooooooo| @ = SCSI ID <0>,<1>,<2>, L +1---------+ (Pins 1,3,5) Remote Busy and Fault Status Display ------------------------------------ The drive's Busy and Fault status can be monitored by connecting a remote Busy and a remote Fault display LED to the drive's Option connector. Remote Busy ----------- The remotely monitor Busy status of the drive, connect the cathode side of the remote Busy LED to the BSY_OUT L pin. The anode side of the LED connects to the +5VDC OUT pin. Remote Fault ------------ The remotely monitor Fault status of the drive, connect the cathode side of the remote Fault LED to the FLT_OUT pin. The anode side of the LED connects to the +5VDC OUT pin. Option Connector +---------20 |ooo oooooo| |ooo***oooo| +1--+++----+ ||+-- +5 VDC OUT |+--- BSY_OUT L +---- FLT_OUT L ********************************************************************** I N S T A L L ********************************************************************** DEC DSP3000 SERIES INSTALLATION GUIDE EK-RH2CA-IG.A01 Notes on installation ===================== Drive mounting -------------- horizontally vertically +-----------------+ +--+ +--+ +------------------+ | | | +-----+ +-----+ | | | | | | | | | | | |+----------------+| +-+-----------------+-+ | | | | | | || || +---------------------+ | | | | | | || || | | | | | | || || | | | | | | || || +---------------------+ | +-----+ +-----+ | || || +-+-----------------+-+ +--+ +--+ || || | | || || | | || || +-----------------+ || || ++----------------++ You can mount the disk drive in any position. The drive (with bezel) attaches to the system bay and accept #6-32 screws. Screws should not exceed 0.25 inch (6.25 millimeters) in length, otherwise damage to the PCB may result. Mounting and Bezel Options -------------------------- Bezels and mounting brackets are available from Digital Equipment Corporation for mounting the drive in either 3.5-inch or 5.25-inch form factor bays. Combination Connector - 8-bit Models ------------------------------------ +-----------------+-----------------------------------------------+ | Part Number | Vendor | +-----------------+-----------------------------------------------+ | 12-36486-01 | Digital Equipment Corp. | +-----------------+-----------------------------------------------+ | 89331-001 | Berg Electronics (formerly Dupont Electronics)| +-----------------+-----------------------------------------------+ | CWN-710-54-0119 | C.W. Industries | +-----------------+-----------------------------------------------+ | DA-2339-25 | Methode Electronics | +-----------------+-----------------------------------------------+ Includes 0.1-in pitch, 50-pin SCSI connector and 4-pin power connector. Combination Connector - 16-bit Models ------------------------------------- +-----------------+-----------------------------------------------+ | Part Number | Vendor | +-----------------+-----------------------------------------------+ | 12-40413-01 | Digital Equipment Corp. | +-----------------+-----------------------------------------------+ | 92-1814-12-1 | AMP, Inc. | +-----------------+-----------------------------------------------+ Includes 68-pin SCSI connector, 4-pin power connector, and a 2-mm pitch, 12-pin (2x6) Option connector. Option Connector - 8-bit Models ------------------------------- +-----------------+-----------------------------------------------+ | Part Number | Vendor | +-----------------+-----------------------------------------------+ | 12-36484-02 | Digital Equipment Corp. | +-----------------+-----------------------------------------------+ | 90516-003 | Berg Electronics (formerly Dupont Electronics)| +-----------------+-----------------------------------------------+ | 3-176837-3 | AMP, Inc. | +-----------------+-----------------------------------------------+ | 87049-2091 | Molex, Inc. | +-----------------+-----------------------------------------------+ A 2-mm pitch, 19-pin (2x10) keyed (missing pin) connector Secondary Option Connector - 16-bit Models ------------------------------------------ +-----------------+-----------------------------------------------+ | Part Number | Vendor | +-----------------+-----------------------------------------------+ | 12-36484-05 | Digital Equipment Corp. | +-----------------+-----------------------------------------------+ A 2-mm pitch, 5-pin (2x3) keyed (missing pin) connector Shunt Jumper - All Models ------------------------- +-----------------+-----------------------------------------------+ | Part Number | Vendor | +-----------------+-----------------------------------------------+ | 12-36482-01 | Digital Equipment Corp. | +-----------------+-----------------------------------------------+ | 86730-001 | Berg Electronics (formerly Dupont Electronics)| +-----------------+-----------------------------------------------+ | LPC-SPG | Honda | +-----------------+-----------------------------------------------+ A 2-mm pitch shunt for configuring termination characteristics Terminating Resistor - DSP3085/3105 ----------------------------------- +-----------------+-----------------------------------------------+ | Part Number | Vendor | +-----------------+-----------------------------------------------+ | 13-26547-01 | Digital Equipment Corp. | +-----------------+-----------------------------------------------+ Resistors are 8-pin, plug resistors. Three required per drive. DC Power and pin connector assignments -------------------------------------- +------------+ pin 1 +12 VDC | 4 3 2 1 | pin 2 +12 Volts Return GROUND +------------+ pin 3 + 5 Volts Return GROUND pin 4 + 5 VDC ********************************************************************** F E A T U R E S ********************************************************************** DEC DSP3000 SERIES INSTALLATION GUIDE EK-RH2CA-IG.A01 Product Summary --------------- DSP3000 Series 3.5-inch Disk Drives are high-performance, high capacity drives, designed and manufactures by Digital Equipment Corporation. Features -------- Features of the DSP3000 Series drives include the following: - Formatted capacity ranging from 852 MB to 2,103 MB, depending upon model - 1 millisecond track-to-track seek time - 512 KB and 1024 KB segmented cache buffer - End-to-end Error Detection Code/Parity on cache RAM - Four headers per sector - Embedded quadrature servo - Self-diagnostics - Down-loadable SCSI firmware - Tagged command queuing - Seek ordering - Automatic block realloction - Glitch-free power on/off operation - Synchronized spindle operation - Low power consumption Seek Time --------- +----------------------------------+--------+--------+--------+ | |DSP3085 |DSP3210 |DSP3160 | | |DSP3105 | | | +----------------------------------+--------+--------+--------+ |Track-to-Track msec. typ. | 1 | 1 | 1 | +----------------------------------+--------+--------+--------+ |Average msec. typ. | 9.5 | 9.5 | 9.7 | | msec. max. | 19 | 20 | 20 | +----------------------------------+--------+--------+--------+ |Latency msec. avg. | 5.6 | 5.6 | 5.6 | +----------------------------------+--------+--------+--------+ LED Indicators -------------- The green Busy LED illuminates to signify the drive is working on a SCSI command. The amber Fault LED indicates a fault status. Both the Busy and Fault indicators light briefly during power up. This serves as a hardware and lamp test. During a calibration operation, the Busy LED is illuminated and the Fault LED flashes. Calibrations occur following some firmware up- grades. Generally, calibration periods last only about five minutes, after which the drive comes online and both indicators go out. If the Fault indicator lights at any other time, the drive has failed and likely requires service (unless the Fault LED was turned on by means of a MODE SELECT command). Remote Busy and Fault indicators can be connected to the Option connector to provide status display at a remote location or panel. Power-On Tests -------------- After power is applied, and before spinup is completed, the drive performs selftest diagnostics prior to making itself visible on the SCSI bus. These intitial selftest check most of the electronics that control HDA, but not the SCSI transceiver or SCSI connector. After spinup, additional tests complete selftest coverage of the electronics module and the HDA. The unit appears not ready to the host between completion of the initial selftests and completion of the drive's post spinup tests.