C F P - 1 0 8 0 S CONNER NO MORE PRODUCED Native| Translation ------+-----+-----+----- Form 3.5"/SLIMLINE Cylinders | | | Capacity form/unform 1080/ MB Heads 6| | | Seek time / track 11.0/ 3.0 ms Sector/track | | | Controller SCSI2 SI/FAST Precompensation Cache/Buffer 256 KB Landing Zone Data transfer rate 4.000 MB/S int Bytes/Sector 512 10.000 MB/S ext SYNC Recording method RLL 1/7 operating | non-operating -------------+-------------- Supply voltage 5/12 V Temperature *C 5 55 | -40 60 Power: sleep 1.0 W Humidity % 8 80 | 8 80 standby 1.0 W Altitude km -0.061 3.048| -0.061 12.192 idle 3.9 W Shock g 5 | 75 seek 5.6 W Rotation RPM 5400 read/write 4.2 W Acoustic dBA 39 spin-up W ECC Bit MTBF h 500000 Warranty Month 60 Lift/Lock/Park YES Certificates ********************************************************************** L A Y O U T ********************************************************************** CONNER CFP-1080S QUICK REFERENCE GUIDE DECEMBER 94, REV. C +---------------------------------------------------------+ | +T1|XX | +-+HDA || |XX | | |Connector || |XX | | | || |XX I | | | || |XX N | +-+ E1-+++ |XX T | +-+++ |XX E J2 | || |XX R | || |XX F | || |XX A |+-+Spin Sync || |XX C ||x|LED Driver T2+ |XX E ||x|J3 ID0+-E1|XX |+-+ ID1| | | 1 0E1+-+ID1 ID2| | |XX J5 ||x|J4 SCSI ID Disable+-+ |XX Power |+-+0E4 Disable Spin Spin |xx1 +---------------------------------------------------------+ ^ | | | | | +---------------------------------------------+ -LED | A3 SS +LED A2 |RESERVED ++ GND | A1 | | | ++ |+--------------------------------+ +++++ ++++++++++ | | | +-++|| | | |||| |||||||||| ++++++++++|| | +--++++-++++++++++-+++++++++++| | | | | +---------------------------------------------------------------+ ********************************************************************** J U M P E R S ********************************************************************** CONNER CFP-1080S QUICK REFERENCE GUIDE DECEMBER 1994, REV. C Jumper Setting ============== S1-S3 SCSI ID ------------- There are three jumpers available for confoguration of SCSI ID: E1, E2, and E3. The following table defines the settings: +----------+-----------------------+ | SCSI ID | Jumpers | | |E3/0E3 |E2/0E2 |E1/0E1 | +----------+-------+-------+-------+ | 0 | OPEN | OPEN | OPEN | +----------+-------+-------+-------+ | 1 | OPEN | OPEN | CLOSED| +----------+-------+-------+-------+ | 2 | OPEN | CLOSED| OPEN | +----------+-------+-------+-------+ | 3 | OPEN | CLOSED| CLOSED| +----------+-------+-------+-------+ | 4 | CLOSED| OPEN | OPEN | +----------+-------+-------+-------+ | 5 | CLOSED| OPEN | CLOSED| +----------+-------+-------+-------+ | 6 | CLOSED| CLOSED| OPEN | +----------+-------+-------+-------+ | 7 | CLOSED| CLOSED| CLOSED| +----------+-------+-------+-------+ Use either but not both: E1 to E3 or 0E1 to 0E3. The 0E header is not installed on drive configurations with a LED on the PCBA. Disable Spin: A jumper in the E4 location, disables spin up on power- on. Disabling spin up on application of power can also be enabled by setting the DSPN bit in MODE SELECT page 0. Termination and Jumpers ----------------------- E1 Enable Term Power Terminators T1, T2: Remove both unless the Drive is the last one on the SCSI Cable. ********************************************************************** I N S T A L L ********************************************************************** CONNER CFP-1080S QUICK REFERENCE GUIDE DECEMBER 1994, REV. C Notes on Installation ===================== J5 Standard 4-pin Power Connector --------------------------------- +----------------------- | +-----J5-----+ +---- pin 1 +12V | | 1 2 3 4 | | 1 pin 2 GND | +------------+ +-- pin 3 GND +------------------ pin 4 +5V Mounting Holes -------------- Side: 6-32 UNC-2B .16 max. insertion Bottom: 6-32 UNC-2B .22 max. insertion