M 2 6 1 8 S A FUJITSU NO MORE PRODUCED Native| Translation ------+-----+-----+----- Form 3.5"/SLIMLINE Cylinders 2010| | | Capacity form/unform 210/ MB Heads 4| | | Seek time / track 16.0/ 5.0 ms Sector/track | | | Controller SCSI1 SINGLE-ENDED Precompensation Cache/Buffer 64 KB Landing Zone Data transfer rate 1.560 MB/S int Bytes/Sector 512 5.000 MB/S ext SYNC Recording method RLL 1/7 operating | non-operating -------------+-------------- Supply voltage 5/12 V Temperature *C 5 50 | -45 60 Power: sleep W Humidity % 20 80 | 5 95 standby W Altitude km 3.000| 12.000 idle W Shock g 5 | 50 seek W Rotation RPM 3490 read/write W Acoustic dBA spin-up W ECC Bit MTBF h 150000 Warranty Month 24 Lift/Lock/Park YES Certificates ********************************************************************** L A Y O U T ********************************************************************** FUJITSU M2617/M2618/S/SA/SB/T rev.A5 (S/N00001-30000) +---------------------------------------------------------+ | +-1-+ |XX | SW1 +-2-+ |XX | +-3-+ |XX I | +-4-+ |XX N | +-5-+ |XX T | +---+ |XX E | |XX R | |XX F | +---+LED +-1-+ |XX A | +---+Connector SW2 +-2-+ |XX C | +-3-+ |XX E | +-4-+ |XX | +-5-+ |XX | +-6-+ |XX | +---+ | | |XX Power | |XX +---------------------------------------------------------+ rev.A6 or higher (S/N 30001 or larger) +---------------------------------------------------------+ | +-1-+ |XX | SW1 +-2-+ |XX | +-3-+ |XX I | +-4-+ |XX N | +-5-+ |XX T | +-6-+ |XX E | +---+ |XX R | |XX F | +---+LED +-1-+ |XX A | +---+Connector SW2 +-2-+ |XX C | +-3-+ |XX E | +-4-+ |XX | +-5-+ |XX | +-6-+ |XX | +---+ | | |XX Power | |XX +---------------------------------------------------------+ ********************************************************************** J U M P E R S ********************************************************************** FUJITSU M2617/M2618/S/SA/SB/T Jumper settting =============== x = Jumpers set at factory O = ON X = OFF Switch setting for rev.A5 (S/N00001-30000) ------------------------------------------ 1 2 3 4 5 +---+---+---+---+---+ | | | | | | SW1 +-+-+-+-+-+-+-+-+-+-+ | | | | +------+ | | | | + IRQ14-21/IRQ14-29 | | | +----------+ | | +--------------- Slave (Active) | +------------------- Active (Slave) +----------------------- OFF (OFF) 1 2 3 4 5 6 +---+---+---+---+---+---+ | | | | | | | SW2 +-+-+-+-+-+-+-+-+-+-+-+-+ | | | | | +------- Reserved | | | | +----------- OFF (OFF) | | | +--------------- Reserved | | +------------------- OFF (OFF) | +----------------------- Reserved +--------------------------- Slave (Master) Words put in parentheses show the setting when they are OFF. SW1/SW2 Default Setting ------------------------ 1 2 3 4 5 +---+---+---+---+---+ x | X | O | X | X | O | SW1 +---+---+---+---+---+ 1 2 3 4 5 6 +---+---+---+---+---+---+ x | X | X | X | X | X | X | SW2 +---+---+---+---+---+---+ SW2 Master/Slave drive ----------------------- 1 +---+ | O | SW2 Slave Drive +---+ 1 +---+ | X | SW2 Master Drive +---+ Switches, SW2-3 and SW2-5, should be always turned off. Alternation of IRQ/Reserved --------------------------- Pin 29 RSVD and pin 31 IRQ 14 can be alternated depending on the host interface. 1 2 3 4 5 Pin 29 = IRQ 14 +---+---+---+---+---+ Pin 31 = Reserved | X | | | O | X | SW1 +---+---+---+---+---+ 1 2 3 4 5 Pin 29 = Reserved +---+---+---+---+---+ Pin 31 = IRQ 14 | X | | | X | O | SW1 +---+---+---+---+---+ SW1 Slave Present ------------------ 1 2 3 4 5 Slave present +---+---+---+---+---+ mode | | X | O | | | SW1 +---+---+---+---+---+ 1 2 3 4 5 Active mode +---+---+---+---+---+ (default) | | O | X | | | SW1 +---+---+---+---+---+ Note: DASP signal is always asserted if switch SW1-2 is off and switch SW1-3 is on. ---------------------------------------------------------------------- Switch setting for rev.A6 or higher (S/N 30001 or larger) --------------------------------------------------------- 1 2 3 4 5 6 +---+---+---+---+---+---+ | | | | | | | SW1 +-+-+-+-+-+-+-+-+-+-+-+-+ | | | | | +------- Reserved | | | | +----------- OFF (OFF) | | | +--------------- Active (Slave) | | +------------------- Slave (Active) | +----------------------+ | + IRQ14-29/IRQ14-31 +--------------------------+ 1 2 3 4 5 6 +---+---+---+---+---+---+ | | | | | | | SW2 +-+-+-+-+-+-+-+-+-+-+-+-+ | | | | | +------- Reserved | | | | +----------- OFF (OFF) | | | +--------------- Reserved | | +------------------- OFF (OFF) | +----------------------- Reserved +--------------------------- Slave (Master) Words put in parentheses show the setting when they are OFF. SW1/SW2 Default Setting ------------------------ 1 2 3 4 5 6 +---+---+---+---+---+---+ x | O | X | X | O | X | X | SW1 +---+---+---+---+---+---+ 1 2 3 4 5 6 +---+---+---+---+---+---+ x | X | X | X | X | X | X | SW2 +---+---+---+---+---+---+ SW2 Master/Slave drive ----------------------- 1 +---+ | O | SW2 Slave Drive +---+ 1 +---+ | X | SW2 Master Drive +---+ Switches, SW2-3 and SW2-5, should be always turned off. Alternation of IRQ/Reserved --------------------------- Pin 29 RSVD and pin 31 IRQ 14 can be alternated depending on the host interface. 1 2 3 4 5 6 Pin 29 = IRQ 14 +---+---+---+---+---+---+ Pin 31 = Reserved | X | O | | | X | | SW1 +---+---+---+---+---+---+ 1 2 3 4 5 6 Pin 29 = Reserved +---+---+---+---+---+---+ Pin 31 = IRQ 14 | X | X | | | O | | SW1 +---+---+---+---+---+---+ SW1 Slave Present ------------------ 1 2 3 4 5 6 Slave present +---+---+---+---+---+---+ mode | | | X | O | | | SW1 +---+---+---+---+---+---+ 1 2 3 4 5 6 Active mode +---+---+---+---+---+---+ (default) | | | O | X | | | SW1 +---+---+---+---+---+---+ Note: DASP signal is always asserted if switch SW1-3 is on and switch SW1-4 is off. ---------------------------------------------------------------------- Daisy chain Connection ---------------------- To a drive which meets ATA standard proposal, daisy chain connection works whether the PB-4'is connected as a master or a slave. To a drive which does not meet ATA standard proposal, daisy chain connection works only under the following conditions: Master: M2617T/M2618T Switch setting: The drive is required to be set to the Active mode. 1 +---+ | X | SW2 +---+ Slave: M2611/2/3/4/6 or M2622/3/4 Switch setting: The slave drive is required to be set to: Slave present mode in the M2611/2/3/4/6 or Active mode in the M2622/3/4 ********************************************************************** I N S T A L L ********************************************************************** FUJITSU M2617/M2618/S/SA/SB/T Notes on installation ===================== Installation direction ---------------------- The drive may be mounted in any attitude! ********************************************************************** F E A T U R E S ********************************************************************** FUJITSU M2617/M2618/S/SA/SB/T Key features ------------ Combining the lastest head, disk, mechanical and electronics technology, Fujitsu has developed two new families of half-height, 3,5-inch hard drives - the M2617 and M2618. The drives, with an embedded SCSI or PC-AT controller, provide a storage capacity of up to 210 megabytes and an average positioning time of 16 milliseconds. All disk enclosures are completely sealed and include one or two disks, four Whitney heads, a rotary voice coil motor (VCM), and a DC spindle motor. High performance ---------------- The M2617 and the M2618 have fast positioning times - 7.0 milli- seconds track-to-track, 16 milliseconds average, and 31 milliseconds maximum, including settling time. The M2617S and the M2618S models have a large, 64 kilobyte data buffer which helps improve the total data transfer rate: 5.00 MB/s synchronous mode and 3.00 MB/s asynchronous mode. The M2617T and the M2618T models also have a 64 kilobyte data buffer and a high data transfer rate: 3.15 megawords per second, or equivalent to 6.30 MB/s. Embedded SCSI or PC-AT controller --------------------------------- The M2617S and the M2618S each have an embedded SCSI controller for quick and easy installation. The controller's commands are compatible with the SCSI CCS (Common Command Set for Direct Access Device). The M2617T and the M2618T have an embedded PC-AT controller, which supports basic PC-AT commands, as well as additional commands. Compact and half-height ----------------------- The compact, one-inch high M2617 and M2618 feature a large storage capacity of 105 MB and 210 MB, respectively. Reliable and maintenance-free ----------------------------- The completely sealed disk enclosure contains a breathing filter and a recirculation filter to provide a contamination-free environment. Whitney heads eliminate moving parts for head loading and unloading. All models use LSI drive logic, and the head IC prevent read errors caused by external electrical noise. With these features, the drive's mean time between failures (MTBF) is more than 150,000 power-on hours, and their mean time to repair (MTTR) is less than 30 minutes. Internationally compatible -------------------------- The M2617 and M2618 disk drives use low-voltage DC supplies of +12V and +5V, permitting international applications and freedom from the effects of power line fluctuations. ********************************************************************** G E N E R A L ********************************************************************** FUJITSU => GDT Tips & Hints about ICP controllers and other peripherals ======================================================== Tagged queues and Fujitsu M 26xx harddisks ------------------------------------------ Fujitsu Harddisks of the M26XX series do not support the SCSI-II feature tagged queues. You should disable this feature in the initialize disks menue of the GDTSetup program. An inquiry command shows, that the harddisk supports tagged queues (this is why you can enable it in the GDTSetup) but this is not true as stated by Fujitsu Germany.