B I G F O O T C Y 6 5 1 0 A T QUANTUM Native| Translation ------+-----+-----+----- Form 5.25"/HH Cylinders |13456| | Capacity form/unform 6510/ MB Heads 6| 16| | Seek time / track 14.0/ 3.0 ms Sector/track | 63| | Controller IDE / ATA2 FAST/ENHA Precompensation Cache/Buffer 128 KB Landing Zone Data transfer rate 11.000 MB/S int Bytes/Sector 512 16.600 MB/S ext PIO4 Recording method PRML 16/17 operating | non-operating -------------+-------------- Supply voltage 5/12 V Temperature *C 5 55 | -40 75 Power: sleep 1.0 W Humidity % 5 85 | 5 95 standby 1.4 W Altitude km -0.061 3.048| 12.192 idle 6.1 W Shock g 10 | 70 seek 7.6 W Rotation RPM 3600 read/write 6.6 W Acoustic dBA 34 spin-up 27.0 W ECC Bit 192BIT,ON THE FLY MTBF h 300000 Warranty Month 36 Lift/Lock/Park YES Certificates CSA,EEC,EN55022-4,EN60950,... ********************************************************************** L A Y O U T ********************************************************************** QUANTUM BIGFOOT CY 2,1/4,3/6,4AT PRODUCT MANUAL 81-113668-01 11/96 8-pin Jumper 40-Pin IDE Connector Connector +----------------------------------------------------+---------+ |* * * * * * * * * * * * * * * * * * * 1 * * * * * | XXXXXXX | |40* * * * * * * * * * * * * * * * * * ++ * * * * | POWER 1| +-----------------------------------------++-+-+-+-+-+---------+ DS+ | | + PARK CS/SP NUSED ********************************************************************** J U M P E R S ********************************************************************** QUANTUM BIGFOOT CY 2,1/4,3/6,4AT PRODUCT MANUAL 81-113668-01 11/96 Jumper Setting ============== 8-pin Jumper Connector ---------------------- 8-pin Jumper Connector -----------------------------+---------+ * * * * * * * 1 * * * * * | XXXXXXX | * * * * * * ++ * * * * | POWER 1| ---------------++-+-+-+-+-+---------+ DS+ | | + PARK CS/SP NUSED The 8-pin embedded connector has two jumper locations, DS and CS/SP, that provide a way to configure the drive's mode operation: - DS - Drive Select - CS/SP - Cable Select/Slave Present A "PARK" position is also provided to store a jumper when it is not in use. DS CS/SP +---+---+---+---PARK |XXX| * | * | * | = MASTER |XXX| * | * | * | +---+---+---+---+ DS CS/SP +---+---+---+---PARK | * | * | * | * | = SLAVE | * | * | * | * | +---+---+---+---+ DS CS/SP +---+---+---+---PARK | * |XXX| * | * | = CABLE SELECT | * |XXX| * | * | +---+---+---+---+ DS CS/SP +---+---+---+---PARK |XXX|XXX| * | * | = MASTER WITH SLAVE PRESENT |XXX|XXX| * | * | +---+---+---+---+ DS CS/SP +---+---+---+---PARK | * | * | * |XXX| = PARK | * | * | * |XXX| +---+---+---+---+ +------+------+------+------------+---------------------------------+ |CS/SP |DS | PARK |Cable Pin 28| Description | +------+------+------+------------+---------------------------------+ |OPEN |OPEN | X | X | Drive is configured as a Slave | +------+------+------+------------+---------------------------------+ |OPEN |CLOSED| X | X | Drive is configured as a Master | +------+------+------+------------+---------------------------------+ |CLOSED|CLOSED| X | X | Drive is configured as a Master,| | | | | | with an attached Slave | +------+------+------+------------+---------------------------------+ |CLOSED| X | X | OPEN | Drive is configured as a Slave | +------+------+------+------------+---------------------------------+ |CLOSED| X | X | GROUND | Drive is configured as a Master | +------+------+------+------------+---------------------------------+ X indicates the jumper setting does not matter. Cable Select/Slave Present (CS/SP) Jumper ----------------------------------------- When the CS jumper is installed, the drive uses pin 28 of the interface connector to determine if the drive is a master or a slave. If pin 28 of the interface connector is grounded, the drive is configured as a Master; if pin 28 of the connector is left open, an internal pullup brings the pin high, and the drive is configured as a Slave. If the CS and internal pullup brings the pin high, and the drive is configured as a Master with an attached Slave. Drive Select (DS) Jumper ------------------------ For systems that do not support the Cable Select feature, a drive can be configured as a Master or Slave by removing the CS jumper and using only the DS jumper. If the DS jumper is installed, the drive is configured as a Master; if it is removed, the drive is configured as a Slave. Park Jumper ----------- The PARK position is used as a place to store a jumper for a Slave drive in systems that do not support Cable Select. Interface Connector Pin 39 -------------------------- DASP- Pin 39 / Drive Active/Slave Present A time-multiplexed signal that indicates either drive activity or that drive 1 is present. During power-on initialization, DASP- is asserted by drive 1 wuthin 400 ms to indicate that drive 1 is present. If drive 1 is not present, drive 0 asserts DASP- after 450 ms to light the drive-activity LED. An open-collector output signal, DASP- is deasserted following the receipt of a valid command by drive 1 or after the drive is ready, whichever occurs first. Once DASP- is deasserted, either hard disk drive can assert DASP- to light the drive activity LED. Each drive has a 10K pull-up resistor on this signal. If an external drive-activity LED is used to monitor this signal, an external resistor must be connected in series between the signal and a +5 volt supply in order to limit the current to 24 mA maximum. ********************************************************************** I N S T A L L ********************************************************************** QUANTUM BIGFOOT CY 2,1/4,3/6,4AT PRODUCT MANUAL 81-113668-02 11/96 Notes On Installation ===================== Installation direction ---------------------- horizontally vertically +-----------------+ +--+ +--+ | | | +-----+ +-----+ | | | | | | | | | +-+-----------------+-+ | | | | | | +---------------------+ | | | | | | | | | | | | | | | | | | +---------------------+ | +-----+ +-----+ | +-+-----------------+-+ +--+ +--+ | | | | +-----------------+ The drive will operate in all axis (6 directions). The mounting holes on the Bigfoot CY 2.1/4.3/6.4AT hard disk drives allow the drive to be mounted in any orientation. IDE-BUS Adapter --------------- There are two ways you can configure a system to allow the Bigfoot CY 2.1/4.3/6.4AT hard disk drives to communicate over the IDE-bus of an IBM or IBM-compatible PC: 1. Connect the drive to a 40-pin IDE-bus connector (if available) on the motherboard of the PC. 2. Install an IDE-compatible adapter board in the PC and connect the drive to the adapter board. 40-Pin IDE Bus Connector ------------------------ Many of the laster design PC motherboards have a built-in 40-pin, IDE-bus connector, that is compatible with the 40-pin IDE interface of the Bigfoot CY 2.1/4.3/6.4AT hard disk drives. If the motherboard has an IDE connector, simply connect a 40-pin ribbon cable between the drive and the motherboard. Adapter Board ------------- If your PC motherboard does not contain a built-in, 40-pin IDE-bus interface connector, you must install an IDE-bus adapter board and connecting cable to allow the drive to interface with the motherboard. Quantum does not supply such an adapter board, but they are available from several third-party vendors. Make sure that the adapter board jumper settings are appropriate. Mounting -------- For mounting, M3 screws are required. To avoid striping the mounting-hole threads, the maximum torque applied to the screws must not exceed 5 kg-cm. Mounting Screw Clearance ------------------------ The printed-circuit board assembly (PCBA) is very close to the mounting holes. CAUTION The PCBA is very close to the mounting holes. Do not exceed the specified length for the mounting screws. The specified screw length allows full use of the mounting-hole threads, while avoiding damaging or placing unwanted stress on the PCBA. Ventilation ----------- The Bigfoot CY 2.1/4.3/6.4AT hard disk drives operates without a cooling fan, provided the ambient air temperature does not exceed 55* C (131*F). Combination Connector --------------------- The connector contains a 40-pin interface, an 8-pin jumper block, and a 4-pin power connector. DC Power Connector ------------------ 4-Pin Connector AMP P/N 1-480424-0 Loose piece contacts AMP P/N 61173-4 Strip contacs: AMP P/N 350078-4 IDE-Bus Interface Connector --------------------------- On the Bigfoot CY 2.1/4.3/6.4AT hard disk drives, the IDE-bus interface cable connector is a 40-pin Universal Header. For mating with the 40-pin connector, recommended cable connectors include the following parts of their equivalents: AMP receptacle with strain relief P/N 1-499506-0 AMP receptacle without strain relief P/N 1-746193-0 To key the 40-pin cable connector, you must plug the hole that corresponds to pin 20. Other recommeded part numbers for the mating connector include: 40-Pin Connector 3M 3417-7000 or equivalent Strain Relief 3M 3448-2040 or equivalent Flat Cable (Stranded 28 AWG) 3M 3365-40 or equivalent Flat Cable (Stranded 28 AWG) 3M 3517-40 (shielded) or equivalent For Systems with a Motherboard IDE Adapter ========================================== You can install the Bigfoot CY hard disk drive in an AT-compatible system that contains a 40-pin AT-bus connector on the motherboard. To connect the drive to the motherboard, use a 40-pin ribbon cable. Ensure that pin 1 of the drive is connected to pin 1 of the mother- board connector. For Systems with an IDE Adapter Board ===================================== To install a Bigfoot CY hard disk drive in an AT-compatible system without a 40-pin, AT-bus connector on its motherboard, you need a third-party IDE-compatible adapter board. Adapter Board Installation -------------------------- Carefully read the manual that accompanies your adapter board before installing it. Make sure that all the jumpers are set properly and that there are no addressing or signal conflicts. Install the adapter board in your system according to the adapter board manual. Connecting the Adapter Board and the Drive ------------------------------------------ Use a 40-pin ribbon cable to connect the drive to the board. 1. Insert the 40-pin cable connector into the mating connector on the adapter board. Make sure that pin 1 of the connector matches with pin 1 on the cable. 2. Insert the other end of the cable into the header on the drive. When inserting this end of the cable, make sure that pin 1 of the cable connects to pin 1 of the drive connector. 3. Secure the drive to the system chassis by using the mounting screws. Base Casting Assembly --------------------- A single-piece aluminium-alloy base casting provides a mounting sur- face for the drive mechanism and PCB. The base casting also acts as the flange for the DC motor assembly. To provide a contamination-free environment for the HDA, a gasket provides a seal between the base casting and the metal cover that enclose the drive mechanism. Air Filtration -------------- The Bigfoot CY AT hard disk drives are Winchester-type drives. The heads fly very close to the media surface. Therefore, it is essential that the air circulating within the drive be kept free of particles. Quantum assembles the drive in a Class-100, purified air environment, then seals the drive with a metal cover. When the drive is in use, the rotation of the disk forces the air inside of the drive through an internal filter. DC Motor Assembly ----------------- Integral with the base casting, the DC motor assembly is a fixed- shaft, brushless DC spindle motor that drives the counter-clockwise rotation of the disks. Electrical Characteristics -------------------------- All signals are transistor-transistor logic (TTL) compatible - with logic 1 greater than 2.0 volts and less than 5.25 volts; and logic 0 greater than 0.0 volts and less than 0.8 volts. Neither the adapter board, motherboard interface, or drives require terminating resistors. Drive Cable and Connector ------------------------- The hard disk drive connects to the host computer by means of a cable. This cable contains a 40-pin connector that plug into the drive, and a 40-pin connector that plugs into the host computer. At the host end, the cable plugs into either an adapter board residing in a host expansion slot or an on-board IDE adapter. If two drives are connected by a cable with two 40-pin drive connectors, the cable-select feature of the Bigfoot CY AT automatically configure each as drive 0 or drive 1 depending on the configuration of pin 28 on the connector. IDE Bus Interface ----------------- A 40-pin IDE interface connector on the motherboard or an adapter board provides an interface between the drive and a host that uses an IBM PC AT bus. The IDE interface contains bus drivers and receivers compatible with the standard AT bus. The AT-bus interface signals D8-D15, INTRQ, and IOCS16- require the IDE adapter board to have an extended I/O-bus connector. The IDE interface buffers data and control signals between the drive and the AT bus of the host system, and decodes addresses on the host address bus. The Command Block Registers on the drive accept commands from the host system BIOS. NOTE Some host systems do not read the Status Register after the drive issues an interrupt. In such cases, the interrupt may not be acknowledged. To overcome this problem, you may have to configure a jumper on the motherboard or adapter board to allow interrupts to be controlled by the drive's interrupt logic. Read your motherboard or adapter board manual carefully to find out how to do this. ********************************************************************** F E A T U R E S ********************************************************************** QUANTUM BIGFOOT CY2,1/4,3/6,4AT PRODUCT MANUAL 81-113668-01 11/96 General Description ------------------- Quantum's Bigfoot CY hard disk drives are a part of a family of high-performance, 0.75-inch-high and 1-inch-high hard disk drives manufactured to meet the highest product quality standards. The Bigfoot CY hard disk drives use nonremovable, 5 1/4-inch hard disks. Bigfoot CY hard disk drives feature an embedded AT drive controller and use ATA commands to optimize systems performance. The drive manages media defects and error recovery internally, so these operations are fully transparent to the user. Seek Times ---------- +-----------------+--------------+ |Track-to-track | 3 ms typ. | +-----------------+--------------+ |Average write | 12 ms typ. | | | 17.0 ms max. | +-----------------+--------------+ |Full stroke | 25 ms typ. | +-----------------+--------------+ System Startup and Operation ---------------------------- Once you have installed the Bigfoot CY hard disk drive and adapter board (if required) in the host system, you are ready to partition and format the drive for operation. To set up the drive correctly, follow these steps: 1. Power on the system 2. Run the SETUP program. This is generally on a Diagnostics or Utilities disk, or within the system's BIOS. 3. Enter the appropriate parameters. The SETUP program allows you to enter the types of optional hard- ware installed - such as the hard disk drive type, the floppy disk drive capacity, and the display adapter type. The system's BIOS uses this information to initialize the system when the power is switched on. For instructions on how to use the SETUP program, refer to the system manual for your PC. During the AT system CMOS setup, you must enter the drive type for the Bigfoot CY hard disk drive. This procedure allows the system to recognize the drive by translating its physical drive geometry parameters such as cylinders, heads, and sectors per track, into a logical addressing mode. 4. Boot the system using the operating system installation disk. 1024 Cylinder Limitation on Older Computer Systems -------------------------------------------------- Because the MS-DOS operating system uses the computer's ROM BIOS to access the hard drive, it is limited to viewing 1,024 cylinders by the AT ROM BIOS. The CMOS System Setup is able to scan the total number of cylinders, but the BIOS is still limited to using only 1024 cylinders. Listed below are some techniques to resolve this difficulty. - Use a third party software program that translates the hard drive parameters to an acceptable configuration for MS-DOS. - Use a hard disk controller that translates the hard drive parameters to an appropriate setup for both MS-DOS, and the computer system's ROM BIOS. Newer Computer Systems with Extended BIOS Translation ----------------------------------------------------- Some newer computer systems allow the user to configure disk drives that go beyond the 528MB (528,482,304 bytes) barrier. Here are formulas to translate drives with a maximum capacity of 8.4 GB (8,422,686,720): xcyl = cyl * nxcyl is defined as a new cylinder translation xhead = head * nxhead is defined as a new head translation xsec = sec = 63xsec is definde as a new sector translation where n = 2, 4, 8, ..., a power of 2 n is chosen to reduce the number of cylinders to be less than or equal to 1024. However, sectors must equal 63 and the number of heads cannot exceed 255. NOTE Be advised that the previous information is dependent upon the capabilities of the computer system, hard disk controller, and/or software programs. Some configurations may not provide the user with proper operation of the disk drive. All other documentation should be examined prior to the hard drive installation. Formatted Capacity ------------------ At the factory, the Bigfoot CY receives a low-level format that creates the actual tracks and sectors on the drive. Data Transfer Rates ------------------- Data is transferred from the disk to the read buffer at a rate up to 6.5 MB/s in burst. Data is transferred from the read buffer to the AT bus at a rate up to 6.0 MB/s, using programmed I/O without IORDY. If IORDY is used, then this transfer rate can be increased to 16.67 MB/s. Reliability ----------- Mean Time Between Failures (MTBF): 300,000 Power On Hours (POH), typical usage Component Life: 5 years Preventive Maintenance (PM): Not required Start/Stop: 20,000 cycles (minimum) The Quantum MTBF numbers represent Bell-Core MTBF predictions and represent the minimum MTBF that Quantum or a customer would expect from the drive. Error Detection and Correction ------------------------------ As disk drive areal densities increase, obtaining extremely low error rate requires a new generation of soghisticated error-correction codes. Quantum Bigfoot CY series hard disk drives implement 224-bit trible-burst Reed-Solomon error correction techniques to reduce the uncorrectable read error rate to less than one bit in 1 x 10(14) bits read. When errors occur, an automatic retry and a more rigorous double- burst and a more rigorous trible.burst correction algorithm enable the correction of any sector with two burst of three incorrect bytes each or up to 12 multiple random one-byte burst errors. In addition to these advanced error correction capabilities, the drive's additional cross-checking code and algorithm double checks the main ECC correction. This greatly reduce the probability of a miscorrection. Automatic Actuator Lock ----------------------- To ensure data integrity and prevent damage during shipment, the drive uses a dedicated landing zone and Quantum's patented AIRLOCK. The AIRLOCK holds the headstack in the landing zone whenever the disks are not rotating. It consists of an air vane mounted near the perimeter of the disk stack and a locking arm that restrains the actuator arm assembly. When DC power is applied to the motor and the disk stack rotates, the rotation generates an airflow on the surface of the disk. As the flow of air across the airvane increases with disk ratation, the locking arm pivots away from the actuator arm, enabling the headstack to move out of the landing zone. When DC power is removed from the motor, a return mechanism automatically pulls the actuator into the landing zone, where the AIRLOCK holds it in place. Disk Caching ------------ The Bigfoot CY hard disk drive incorporates DisCache, an 78K disk cache, to enhance drive performance. This integrated feature is user-programmable and can significantly improve system throughput. Read and write caching can be enabled or disabled by using the SET CONIGURATION command. Error Reporting --------------- At the start of a command's execution, the Bigfoot CY hard disk drive checks the Command Register for any conditions that would lead an abort command error. The drive then attemps execution of the command. Any new error causes execution of the command to terminate at the point at which it is occurred. -----------------+--------------------------+---------------------+ COMMAND |ERROR REGISTER |STATUS REGISTER | +--------------------------+---------------------+ |BBK|UNC|IDNF|ABRT|TK0|AMNF|DRDY|DWF|DSC|CORR|ERR| -----------------+---+---+----+----+---+----+----+---+---+----+---+ Check Power Mode | | | | V | | | V | V | V | | V | -----------------+---+---+----+----+---+----+----+---+---+----+---+ Read Defect List | V | V | V | V | | V | V | V | V | V | V | -----------------+---+---+----+----+---+----+----+---+---+----+---+ Exec. Drive Diag.| | | | | | | | | | | V | -----------------+---+---+----+----+---+----+----+---+---+----+---+ Format Track | | | V | V | | | V | V | V | | V | -----------------+---+---+----+----+---+----+----+---+---+----+---+ Identify Drive | | | | V | | | V | V | V | | V | -----------------+---+---+----+----+---+----+----+---+---+----+---+ Initi. Parameters| | | | | | | V | V | V | | | -----------------+---+---+----+----+---+----+----+---+---+----+---+ Inval.Cmnd. Codes| | | | V | | | V | V | V | | V | -----------------+---+---+----+----+---+----+----+---+---+----+---+ Read Buffer | | | | V | | | V | V | V | | V | -----------------+---+---+----+----+---+----+----+---+---+----+---+ Read Configurati.| V | V | V | V | | V | V | V | V | V | V | -----------------+---+---+----+----+---+----+----+---+---+----+---+ Read DMA | V | V | V | V | | V | V | V | V | V | V | -----------------+---+---+----+----+---+----+----+---+---+----+---+ Read Multiple | V | V | V | V | | V | V | V | V | V | V | -----------------+---+---+----+----+---+----+----+---+---+----+---+ Read Sectors | V | V | V | V | | V | V | V | V | V | V | -----------------+---+---+----+----+---+----+----+---+---+----+---+ Read Sec. Long | V | | V | V | | V | V | V | V | | V | -----------------+---+---+----+----+---+----+----+---+---+----+---+ Read Verify Sec. | V | V | V | V | | V | V | V | V | V | V | -----------------+---+---+----+----+---+----+----+---+---+----+---+ Recalibrate | | | | V | V | | V | V | V | | V | -----------------+---+---+----+----+---+----+----+---+---+----+---+ Seek | | | V | V | | | V | V | V | | V | -----------------+---+---+----+----+---+----+----+---+---+----+---+ Set Configuration| V | | V | V | | | V | V | V | | V | -----------------+---+---+----+----+---+----+----+---+---+----+---+ Set Features | | | | V | | | V | V | V | | V | -----------------+---+---+----+----+---+----+----+---+---+----+---+ Set Multiple Mode| | | | V | | | | | | | V | -----------------+---+---+----+----+---+----+----+---+---+----+---+ Write Buffer | | | | V | | | | | | | V | -----------------+---+---+----+----+---+----+----+---+---+----+---+ Write Multiple | V | | V | V | | | V | V | V | | V | -----------------+---+---+----+----+---+----+----+---+---+----+---+ Write DMA | V | | V | V | | | V | V | V | | V | -----------------+---+---+----+----+---+----+----+---+---+----+---+ Write Sectors | V | | V | V | | | V | V | V | | V | -----------------+---+---+----+----+---+----+----+---+---+----+---+ Write Sec. Long | V | | V | V | | | V | V | V | | V | -----------------+---+---+----+----+---+----+----+---+---+----+---+ Key: V = Valid errors for each command ABRT = Abort command error AMNF = Data address mark not found error BBK = Bad block detected CORR = Corrected data error DRDY = Drive not ready detected DSC = Disk seek complete not detected DWF = Drive write fault detected ERR = Error bit in the Status Register IDNF = Requested ID not found TK0 = Track zero not found error UNC = Uncorrectable data error Defect Management ----------------- In the factory, the media is scanned for defects. If a sector on a cylinder is found to be defective, the address of the sector is added to the drive's defect list. Sectors located physically subsequent to the defective sector are assigned logical block addresses such that a sequential ordering of logical blocks results. This inline sparing technique is employed in an attempt to eliminate slow data transfer that would result from a single defective sector on a cylinder. ********************************************************************** G E N E R A L ********************************************************************** QUANTUM ATA TIPS Comparing the Fast ATA and Enhanced IDE Disk Drive Interfaces ------------------------------------------------------------- Why are Fast ATA and Fast ATA-2 Important? Faster data transfer rates are important because a computer is only as fast as its slowest component. Today's 486, Pentium, and PowerPC-based computers offer processor speeds many times faster than only two years ago. Bus speeds have also increased with the inclusion of 32-bit VL and PCI local buses, which have a maximum data transfer rate of 132 MB/second. Faster buses mean that data can be transferred from the storage device to the host at greater speeds. Fast ATA and Fast ATA-2 allow disk drives to store and access this data faster, thus enhancing the other high-speed components in the system and removing the bottleneck associated with older ATA/IDE drives. In short, Fast ATA helps bring very high performance to desktop PC systems. In addition, when compared to SCSI, Fast ATA is the least expensive way to achieve faster disk drive data transfer rates and higher system performance. The implementation of Fast ATA through system BIOS provides performance without incremental hardware co sts. Older systems can support Fast ATA using an inexpensive host adapter. Fast ATA and Fast ATA-2 are easy to implement in either VL or PCI local bus systems. The hardware connection can be made using a standard 40-pin ATA ribbon cable from the drive to the host adapter. Direct connection to the motherboard further eases integration when provided by the motherboard supplier. Once connected, the high data transfer capabilities of Fast ATA can be enabled through the data transfer options found in most CMOS BIOS setup tables. Newer versions of BIOS provide automatic configuration for Fast ATA drives. Fast ATA can improve efficiency by allowing more work to be completed in less time because the computer moves data faster. Graphic, multimedia, and audio/visual software users will benefit most because the speed of those applications, which work with large blocks of data, are transfer-rate dependent. The Fast ATA and Enhanced IDE interfaces both use the local bus to speed data transfer rates. Enhanced IDE also uses the same PIO modes as Fast ATA, although a data transfer rate equal to the PIO mode 4 rate has not been announced for Enhanced IDE. The major differences between Fast ATA and Enhanced IDE are that the latter includes three distinct features in addition to fast data transfer rates. The additional features of Enhanced IDE are as follows: High-capacity addressing of ATA hard drives over 528 MB - a BIOS and device driver function. Dual ATA host adapters supporting up to four hard disk drives per computer system - a function of BIOS, operating system, and host adapter, not the drive. Support for non-hard disk drive peripherals such as CD-ROMs - a function of BIOS and the operating system, not the drive Each of these features supports improved functionality at a system level, a positive development for the industry and end users. However, support for all three features requires an extremely high degree of integration and revisions to operating systems and hard- ware, in addition to BIOS changes. Specific support is required not only for the storage peripherals but also for host adapters, core logic, the system bus, BIOS, and operating systems - virtually every major block of PC architecture. There is no central industry-supported standard that controls the features of Enhanced IDE. With no standard, some products sold as "Enhanced" may provide only one of the three features of Enhanced IDE. For example, fast data transfer rate support is be coming standard on mid-range and high-end local bus systems. This single feature could satisfy the users immediate requirements without the need for the other features of Enhanced IDE. In the future, if the same system is upgraded to add the remaining features of Enhanced IDE, users may be forced to purchase an Enhanced IDE package that contains a feature already installed. This could result in unnecessary costs, integration conflicts, and in- compatibility with original factory implementations. Fast ATA, on the other hand, represents only the fast data transfer rates for ATA hard drives (support for PIO mode 3 or 4 and DMA mode 1 or 2). Fast ATA and Fast ATA-2 data transfer rates can be easily achieved when the system BIOS and hard drive suppo rt the PIO and DMA protocols. BIOS that supports Fast ATA does not necessarily support high- capacity addressing, dual host adapters or non-hard drive peripherals. But these features are being introduced independently by system manufacturers in order to compete in the PC marketplace. All of Quantum's disk drives designed for PCs now support Fast ATA, and new products with Fast ATA support will be introduced in early 1995. The drives are also fully backward compatible with older ATA/ IDE (non-Fast ATA) BIOS. The Quantum drives support both the Extended CHS (Cylinder Head Sector) and LBA (Logical Block Address) addressing methods in overcoming the 528 MB DOS capacity barrier. Quantum drives can also be used with dual host adapters. Finally, there are no incompatibilities with Quantum hard drives that would prevent computer systems from supporting non-hard drive peripherals. Quantum drives that support Fast ATA include the following families: Quantum ProDrive LPS 170/210/340/420 Quantum ProDrive LPS 270/540 Quantum Maverick 270/540 Quantum Lightning 365/540/730 Quantum Daytona 127/170/256/341/514 Fast ATA and Fast ATA-2 are important technologies that can take advantage of the performance provided by the latest high-speed microprocessors and bus architectures. The high-speed interfaces are based on industry standard specifications and are the least expensive way to achieve faster disk drive data transfer rates. Fast ATA is not a group of features that requires an extremely high level of integration, and only represents the fast data transfer rates for ATA hard drives (PIO mode 3 or 4 and DMA mode 1 or 2). =====================================================================