3 3 8 7 W S SINGAPORE Native| Translation ------+-----+-----+----- Form 3.5"/HH Cylinders 4811| | | Capacity form/unform 8700/ MB Heads | | | Seek time / track 7.9/ ms Sector/track | | | Controller SCSI3 SI/WI/ULTRA Precompensation Cache/Buffer KB Landing Zone Data transfer rate MB/S int Bytes/Sector 512 40.000 MB/S ext SYNC Recording method operating | non-operating -------------+-------------- Supply voltage 5/12 V Temperature *C | Power: sleep W Humidity % | standby W Altitude km | idle 14.0 W Shock g | seek 17.0 W Rotation RPM 7200 read/write W Acoustic dBA spin-up W ECC Bit MTBF h 650000 Warranty Month Lift/Lock/Park YES Certificates ********************************************************************** L A Y O U T ********************************************************************** MICROPL. 3387 WS NOTES ON INSTALATION +---------------------------------------------------------+ XX |XX XX TEST CONNECTOR |XX XX (factory use only) |XX XX |XX | |XX J1 ++LED |XX ++ |XX | |XX | |XX XX 1 |XX XX |XX XX |XX XX Option Jumper |XX XX Block |XX1 XX |XX XX |XX J1A | |XX +---------------------------------------------------------+ 1 ********************************************************************** J U M P E R S ********************************************************************** MICROPL. 3387/4341/4345 WS NOTES ON INSTALLATION Jumper Setting ============== x = Factory default Drive Option Selection ---------------------- +------------------- SP1 | +---------- ID2 | | +------- ID1 | | | +---- ID0 W3 W2 W1 W4 KEY KEY | | | | +- Remote LED+ +--+-++-++-++-++-++--+--+-++--+--+-++--+--+-++-++-++-++ |35|33|31|29|27|25|23|21|19|17|15|13|11|09|07|05|03|01| +--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ |36|34|32|30|28|26|24|22|20|18|16|14|12|10|08|06|04|02| +-++--+--+--+--+--+-++-++--+-++-++--+-++-++--+--+--+-++ | | | | WP | | +- Remote LED- | | | PTY | | | | | | +------------- ID3 | | | +---------------- SP0 +--- RESERVED | +------------------------------- RESERVED +---------------------------------- RESERVED NOTE Pin 4, 6, 8, 10, 12, 14, 16, 18, 22, and 24 are tied to Ground. Option Jumper Block J2 is a 36-pin connector used for drive addressing and various configuration options. SCSI ID ------- Jumpers at Pin 3-4, 5-6, 7-8, and 9-10 select the SCSI ID. Each SCSI device on one Host Adapter must have a unique SCSI ID. +----------+-------------------------------+ | SCSI ID | Jumper Location | | | PINS | | | ID3 | ID2 | ID1 | ID0 | +----------+-------+-------+-------+-------+ | 0 | OPEN | OPEN | OPEN | OPEN | DEFAULT +----------+-------+-------+-------+-------+ | 1 | OPEN | OPEN | OPEN | CLOSED| +----------+-------+-------+-------+-------+ | 2 | OPEN | OPEN | CLOSED| OPEN | +----------+-------+-------+-------+-------+ | 3 | OPEN | OPEN | CLOSED| CLOSED| +----------+-------+-------+-------+-------+ | 4 | OPEN | CLOSED| OPEN | OPEN | +----------+-------+-------+-------+-------+ | 5 | OPEN | CLOSED| OPEN | CLOSED| +----------+-------+-------+-------+-------+ | 6 | OPEN | CLOSED| CLOSED| OPEN | +----------+-------+-------+-------+-------+ | 7 | OPEN | CLOSED| CLOSED| CLOSED| +----------+-------+-------+-------+-------+ | 8 | CLOSED| OPEN | OPEN | OPEN | +----------+-------+-------+-------+-------+ | 9 | CLOSED| OPEN | OPEN | CLOSED| +----------+-------+-------+-------+-------+ | 10 | CLOSED| OPEN | CLOSED| OPEN | +----------+-------+-------+-------+-------+ | 11 | CLOSED| OPEN | CLOSED| CLOSED| +----------+-------+-------+-------+-------+ | 12 | CLOSED| CLOSED| OPEN | OPEN | +----------+-------+-------+-------+-------+ | 13 | CLOSED| CLOSED| OPEN | CLOSED| +----------+-------+-------+-------+-------+ | 14 | CLOSED| CLOSED| CLOSED| OPEN | +----------+-------+-------+-------+-------+ | 15 | CLOSED| CLOSED| CLOSED| CLOSED| +----------+-------+-------+-------+-------+ SP0/SP1 Spindle Control Option ------------------------------- SP0 CLOSED SP1 OPEN Spindle motor starts when START UNIT command is received. SP0 OPEN (default) SP1 OPEN Spindle motor starts at power-on. SP0/SP1 Spindle Delay Option ----------------------------- SP1 CLOSED SP0 OPEN Spindle start-up is delayed based on SCSI ID (12 seconds per ID). SP1 OPEN (default) SP0 OPEN Spindle motor starts at power on. WP Write Protect Option ------------------------ WP CLOSED Drive is write protected. WP OPEN Drive is not write protected. (default) PTY Bus Parity Check Option ---------------------------- PTY CLOSED Drive neither generates nor detects parity. OPEN Drive generates parity and has parity detection enabled. (default) W1/W2/W3 Bus Termination Power Option -------------------------------------- W1 CLOSED (default) Drive provides terminator power. W2 CLOSED Host system provides terminator power (via J1). W3 CLOSED Drive provides terminator power (via J1) to the BUS. W4 Interface Termination ------------------------ W4 INSTALLED Drive provides termination for the interface lines; i.e., onboard termination is electrically enabled. x OMITTED Drive does not provide terminatiopn for the inter- face lines; i.e., onboard termination is electrically disabled. Remote LED ---------- Open Collector output - Used to drive a user-supplied LED to indicate the drive as active.