QUATECH, INC.
CTM-10/CTM-11
|
Category |
Counter/timer |
|
Chipset Controller |
Unidentified |
|
I /O Options Supported |
Timing signal input via module connector |
|
Maximum Onboard Memory |
N/A |
|
CONNECTIONS |
|||
|
Purpose |
Location |
Purpose |
Location |
|
Input/Output signal connector |
H1 |
Expansion card connector |
H2 |
|
SIGNAL TYPE |
||||||
|
Setting |
J2 |
J3 |
J4 |
J5 |
J6 |
J7 |
|
Preconditioned |
Jumper A |
Jumper A |
Jumper A |
Jumper A |
Jumper A |
Jumper A |
|
Mechanical switch |
Jumper B |
Jumper B |
Jumper B |
Jumper B |
Jumper B |
Jumper B |
|
Non-ideal |
Jumper C |
Jumper C |
Jumper C |
Jumper C |
Jumper C |
Jumper C |
|
Note: The jumpers indicated are in the closed position. |
||||||
|
CHANNEL 0 EXTERNAL LEVEL INPUT SIGNAL |
||
|
Setting |
J8/jumper A |
J10/jumper A |
|
Counter 0 level input signal enabled |
Closed |
Closed |
|
Counter 0 level input signal disabled |
Open |
Open |
|
CHANNEL 1 EXTERNAL LEVEL INPUT SIGNAL |
||
|
Setting |
J9/jumper A |
J10/jumper A |
|
Counter 1 level input signal enabled |
Closed |
Closed |
|
Counter 1 level input signal disabled |
Open |
Open |
|
COUNTER |
|||
|
Setting |
J5/jumper D |
J6/jumper D |
J7/jumper D |
|
Counter 0 enabled |
Closed |
N/A |
N/A |
|
Counter 1 enabled |
N/A |
Closed |
N/A |
|
Counter 2 enabled |
N/A |
N/A |
Closed |
|
COUNTER CASCADING |
|||
|
Setting |
J6/jumper E |
J7/jumper E |
J7/jumper F |
|
Counters 0 and 1 cascaded |
Closed |
Open |
Open |
|
Counter 0 and 2 cascaded |
Open |
Closed |
Open |
|
Counter 1 and 2 cascaded |
Open |
Open |
Closed |
|
All three counters cascaded |
Closed |
Open |
Closed |
|
PULSE WIDTH MEASUREMENT |
||||
|
Setting |
J5/jumper D |
J6/jumper E |
J8/jumper B |
J9/jumper B |
|
Measured at Counter 0 |
Closed |
N/A |
Closed |
N/A |
|
Measured at Counter 1 |
N/A |
Closed |
N/A |
Closed |
|
Note (1):For single pulse width measurement, connect the input signal to pins 10 and 11 of header H1. Note (2):For pulse width measurement between two pulses, connect one signal to pin 10 of header H1 and the other signal to pin 11 of header H1. |
||||
|
MISCELLANEOUS TECHNICAL NOTES |
|
The CTM-10/CTM-11 is a modular daughter-card designed to work with the Quatech PXB-721 or MXI-241. Header H1 signal connections are as follows: pins 1 - 3 = CLK 0 - 2, respectively, pins 4 - 6 = Pulse Output 0 - 2, respectively, pins 7 - 9 = External Input 0 - 2, respectively, pins 10 and 11 = Pulse Input 1 and 2, respectively. Pins 14 - 26 are connected to ground and pins 12 and 13 are unused. The purpose of all other jumpers on this card are not identified in manufacturer's documentation. |