THOMAS-CONRAD CORPORATION

TC3045-ST (Fiber Optic) TCNS 16-BIT

NIC Type

TCNS (proprietary)

Transfer Rate

100Mbps

Data Bus

16-bit ISA

Topology

Star

Wiring Type

Fiber optic cable

Boot ROM

Not Available

NODE ADDRESS

Node

SW2/1

SW2/2

SW2/3

SW2/4

SW2/5

SW2/6

SW2/7

SW2/8

0

-

-

-

-

-

-

-

-

1

On

On

On

On

On

On

On

Off

2

On

On

On

On

On

On

Off

On

3

On

On

On

On

On

On

Off

Off

4

On

On

On

On

On

Off

On

On

251

Off

Off

Off

Off

Off

On

Off

Off

252

Off

Off

Off

Off

Off

Off

On

On

253

Off

Off

Off

Off

Off

Off

On

Off

254

Off

Off

Off

Off

Off

Off

Off

On

255

Off

Off

Off

Off

Off

Off

Off

Off

Notes:Node address 0 is used for messaging between nodes and must not be used. A total of 255 node address settings are available. The switches are a binary representation of the decimal node addresses. Switch 8 is the Least Significant Bit and switch 1 is the Most Significant Bit. The switches have the following decimal values: switch 8=1, 7=2, 6=4, 5=8, 4=16, 3=32, 2=64, 1=128. Turn Off the switches and add the values of the Off switches to obtain the correct node address. (On=0, Off=1)

CONNECTIONS

Purpose

Location

Receive (dark colored)

CN1

Transmit data (light colored)

CN2

BLOCK DECODE SIZE

Size

JP1

»

16KB

Pins 2 & 3 closed

 

128KB

Pins 1 & 2 closed

Note:A 16-bit VGA adapter typically decodes base memory in 128KB blocks. If you are installing the NIC in a system with such a card, you may need to set the NIC block decode size to 128KB. If you set the block decode size to 128KB then all other adapters in the system must also utilize 128KB decode.

ZERO WAIT STATE

Setting

JP3

»

Enabled

On

 

Disabled

Off

INTERRUPT REQUEST

IRQ

JP5

JP6

JP7

JP8

JP9

JP10

JP11

JP12

JP13

JP14

JP15

»

2

Open

Open

Open

Open

Open

Closed

Open

Open

Open

Open

Open

 

3

Open

Open

Open

Open

Open

Open

Closed

Open

Open

Open

Open

 

4

Open

Open

Open

Open

Open

Open

Open

Closed

Open

Open

Open

 

5

Open

Open

Open

Open

Open

Open

Open

Open

Closed

Open

Open

 

6

Open

Open

Open

Open

Open

Open

Open

Open

Open

Closed

Open

 

7

Open

Open

Open

Open

Open

Open

Open

Open

Open

Open

Closed

 

10

Open

Open

Open

Open

Closed

Open

Open

Open

Open

Open

Open

 

11

Open

Open

Open

Closed

Open

Open

Open

Open

Open

Open

Open

 

12

Open

Open

Closed

Open

Open

Open

Open

Open

Open

Open

Open

 

14

Open

Closed

Open

Open

Open

Open

Open

Open

Open

Open

Open

 

15

Closed

Open

Open

Open

Open

Open

Open

Open

Open

Open

Open

BASE MEMORY ADDRESS

Address

SW1/1

SW1/2

SW1/3

SW1/4

SW1/5

SW1/6

»

D000h

Off

Off

On

Off

On

On

 

C000h

Off

Off

On

On

On

On

 

C400h

Off

Off

On

On

On

Off

 

C800h

Off

Off

On

On

On

On

 

CC00h

Off

Off

On

On

Off

Off

 

D400h

Off

Off

On

Off

On

On

 

D800h

Off

Off

On

Off

Off

On

 

DC00h

Off

Off

On

Off

Off

Off

 

Note : SW1/7 & SW1/8 are always in the on position.

OPERATING MODE

Mode

SW3/7

»

Enhanced mode

On

 

Compatible mode

Off

Note: Enhanced mode optimizes performance and minimizes conflicts of your hardware by using a Thomas-Conrad ARCNET driver. It is also not necessary to set the I/O address. In compatible mode the adapter can use most existing ARCNET drivers.

I/O BASE ADDRESS

Address

SW3/1

SW3/2

SW3/3

SW3/4

SW3/5

SW3/6

»

2E0h

Off

On

Off

Off

Off

On

 

2F0h

Off

On

Off

Off

Off

Off

 

300h

Off

Off

On

On

On

On

 

310h

Off

Off

On

On

On

Off

 

320h

Off

Off

On

On

Off

On

 

330h

Off

Off

On

On

Off

Off

 

340h

Off

Off

On

Off

On

On

 

350h

Off

Off

On

Off

On

Off

 

360h

Off

Off

On

Off

Off

On

 

370h

Off

Off

On

Off

Off

Off

 

380h

Off

Off

Off

On

On

On

 

390h

Off

Off

Off

On

On

Off

 

3A0h

Off

Off

Off

On

Off

On

 

3B0h

Off

Off

Off

On

Off

Off

 

3C0h

Off

Off

Off

Off

On

On

 

3D0h

Off

Off

Off

Off

On

Off

 

3E0h

Off

Off

Off

Off

Off

On

 

3F0h

Off

Off

Off

Off

Off

Off

FACTORY CONFIGURED SETTINGS

Jumper/Switch

Setting

JP2

N/A

SW3/8

N/A