Card Type	Fax, Modem (asynchronous)
Chip Set	Unidentified
Maximum Data Rate	14.4Kbps
Maximum Fax Rate	14.4Kbps
Data Bus	PCMCIA Type II
Fax Class	Class I
Data Modulation Protocol	Bell 103/212A ITU-T V.21, V.22, V.22bis, V.32, V.32bis
Fax Modulation Protocol	ITU-T V.17, V.21CH2, V.27ter, V.29
Error Correction/Compression	MNP5, V.42, V.42bis

ACCEPT MNP RELIABLE MODE
Type:	Immediate
Format:	AT [cmds] \U [cmds]
Description:	Accept remote modem’s request for MNP reliable mode

AUTO-FALLBACK/FALL-FORWARD
Type:	Configuration
Format:	AT [cmds] %Gn [cmds]
Description:	Selects auto-fallback/fall-forward
Command	Function
í %G0	Auto-fallback/fall-forward disabled
%G1	Auto-fallback/fall-forward enabled

AUTO-RELIABLE FALLBACK CHARACTER
Type:	Configuration
Format:	AT [cmds] %An [cmds]
Default:	Unidentified
Range:	0-127
Unit:	ASCII
Description:	Sets the character used as the auto-reliable fallback character; %A0 will disable this function.

AUTO-RELIABLE TIME BUFFER CONFIGURATION
Type:	Configuration
Format:	AT [cmds] \Cn [cmds]
Description:	Controls the handling of incoming data during auto-reliable time period
Command	Function
í \C0	Data is discarded
\C1	Data is buffered
\C2	Data is discarded; modem returns to normal mode on receiving auto-reliable fallback character.

AUTO-RETRAIN
Type:	Configuration
Format:	AT [cmds] %En [cmds]
Description:	Controls auto-retrain mode
Command	Function
%E0	Auto-retrain disabled
í %E1	Auto-retrain enabled

BIT MAPPED REGISTERS
Register	Default
S14	Unidentified
S21	Unidentified
S22	Unidentified
S23	Unidentified
S27	Unidentified

BREAK SEND
Type:	Configuration
Format:	AT [cmds] \Bn [cmds]
Default:	3
Range:	1-9
Unit:	.1 second
Description:	Sends break to modem

BREAK TYPE
Type:	Configuration
Format:	AT [cmds] \Kn [cmds]
Default:	5
Range:	0-5
Description:	Configures action of break signal

COMPRESSION
Type:	Configuration
Format:	AT [cmds] %Cn [cmds]
Description:	Selects data compression
Command	Function
%C0	Data compression disabled
í %C1	MNP5 enabled

CONNECT MODE
Type:	Configuration
Format:	AT [cmds] \Nn [cmds]
Description:	Controls the type of connection the modem will operate in
Command	Function
\N0	Normal mode enabled
\N1	Direct mode enabled
\N2	MNP reliable mode enabled
í \N3	Auto-reliable mode enabled
\N4	V.42 reliable mode enabled

CONVERT TO MNP RELIABLE MODE
Type:	Immediate
Format:	AT [cmds] \Y [cmds]
Description:	Converts to MNP reliable mode from normal or direct mode

FLOW CONTROL
Type:	Configuration
Format:	AT [cmds] \Gn [cmds]
Description:	Selects modem port flow control
Command	Function
í \G0	Flow control disabled
\G1	Flow control enabled

FLOW CONTROL TYPE
Type:	Configuration
Format:	AT [cmds] \Qn [cmds]
Description:	Sets type of flow control used by modem
Command	Function
\Q0	Flow control disabled
\Q1	Bidirectional XON/XOFF flow control enabled
\Q2	CTS flow control by DCE enabled
í \Q3	Bidirectional RTS/CTS flow control enabled

EXTENDED RESULT CODES
Type:	Configuration
Format:	AT [cmds] \Vn [cmds]
Description:	Selects extended result codes
Command	Function
\V0	Extended result codes disabled
\V1	Extended result codes set 1 enabled
í \V2	Extended result codes set 2 enabled

INACTIVITY TIMER
Type:	Configuration
Format:	AT [cmds] \Tn [cmds]
Default:	0
Range:	0-90
Unit:	1 minute
Description:	Sets the length of time that the modem does not receive information before it disconnects.

INACTIVITY TIMER
Type:	Register
Format:	AT [cmds] S90=n [cmds]
Default:	0
Range:	0-255
Unit:	1 second
Description:	Sets the length of time that the modem does not receive information before it disconnects; S90=0 will disable.

INITIATE MNP RELIABLE MODE
Type:	Immediate
Format:	AT [cmds] \O [cmds]
Description:	Initiates MNP reliable mode from normal

LOCK SERIAL PORT
Type:	Configuration
Format:	AT [cmds] \Jn [cmds]
Description:	Sets operation of serial port speed
Command	Function
í \J0	Serial speed locked
\J1	Serial speed follows connect speed

MAXIMUM BLOCK SIZE FOR TRANSMISSION
Type:	Configuration
Format:	AT [cmds] \An [cmds]
Description:	Sets the maximum transmittable block size
Command	Function
\A0	MNP block size is 64 characters
\A1	MNP block size is 128 characters
\A2	MNP block size is 192 characters
í \A3	MNP block size is 256 characters

REPORT INFORMATION
Type:	Immediate
Format:	AT [cmds] In [cmds]
Description:	Displays information requested
Command	Function
I0	Reports product identification code
I1	Reports ROM checksum
I2	Internal memory test
I3	Reports device ID
I4	Reports internal ID

SWITCH TO NORMAL MODE
Type:	Immediate
Format:	AT [cmds] \Z [cmds]
Description:	Switches to normal mode from MNP mode

TEST MODES
Type:		Register
Format:		AT [cmds] S16=n [cmds]
Default:		Unidentified
Range:		0-125
Unit:		Bit-mapped
Description:		Controls loopback tests, analog, digital, remote digital, and self tests.
Bit	Value	Function
0	0 1	Local analog loopback not in progress Local analog loopback in progress
1	0	Not used
2	0 1	Local digital loopback not in progress Local digital loopback in progress
3	0 1	Modem not in remote digital loopback Remote digital loopback in progress
4	0 1	Remote digital loopback not requested Remote digital loopback requested
5	0 1	Remote digital loopback w/ self-test not in progress Remote digital loopback w/ self-test in progress
6	0 1	Local analog loopback w/ self-test not in progress Local analog loopback w/ self-test in progress

V.42 - DETECTION PHASE
Type:	Configuration
Format:	AT [cmds] -Jn [cmds]
Description:	Controls V.42 detection
Command	Function
-J0	V.42 detection disabled
í -J1	V.42 detection enabled

V.42bis - COMPRESSION CONTROL
Type:	Configuration
Format:	AT [cmds] "Hn [cmds]
Description:	Controls V.42bis data compression
Command	Function
"H0	V.42bis disabled
"H1	V.42bis when transmitting enabled
"H2	V.42bis when receiving enabled
í "H3	V.42bis when transmitting/receiving enabled

V.42bis - MAXIMUM STRING LENGTH
Type:	Immediate
Format:	AT [cmds] "On [cmds]
Default:	16
Range:	6-250
Unit:	Characters
Description:	Selects string size for V.42bis compression

XON/XOFF PASS-THROUGH
Type:	Configuration
Format:	AT [cmds] \Xn [cmds]
Description:	Selects whether XON/XOFF signals are sent to remote modem
Command	Function
í \X0	XON/XOFF signals trapped by local modem
\X1	XON/XOFF passed through local modem