MAXTECH CORPORATION

XM 144IC (CL-MD1414ECT-SP)

Card Type

Modem/Fax card

Chip Set

Unidentified

I/O Options

Line in(RJ-11), line out(RJ-11), speaker out, microphone in

Maximum Modem Rate

14.4Kbps

Maximum Fax Rate

14.4Kbps

Data Modulation Protocol

Bell 103/212A, ITU-T V.22bis, V.22, V.32, V.32bis, V.21

Fax Modulation Protocol

ITU-T V.27ter, V.29, V.17

Error Correction/Compression

MNP5, V.42bis, V.42

Fax Class

Class I

Data Bus

8-bit ISA

CONNECTIONS

Function

Label

Function

Label

RJ-11 line

CN1

Speaker out

CN3

RJ-11 line

CN2

Microphone in

CN4

SERIAL PORT ADDRESS

Setting

SW1/1

SW1/2

í COM1 (3F8h)

On

On

COM2 (2F8h)

Off

On

COM3 (3E8h)

On

Off

COM4 (2E8h)

Off

Off

INTERRUPT

Setting

SW1/3

SW1/4

SW1/5

SW1/6

IR/FONT>

On

Off

Off

Off

IRQ3

Off

On

Off

Off

í IRQ4

Off

Off

On

Off

IRQ5

Off

Off

Off

On

 

SUPPORTED COMMAND SET

Basic AT Commands

AT, +++, A/

A, B, E, H, M, O, P, Q, T, V, X, Y, Z

&C, &F, &G, &T, &W, &Y, &Z

Extended AT Commands

\A, \B, \C, \G, \J, \K, \O, \U, \X, \Y, \Z

%A

"H

-J

S Registers

S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S25

S26, S27, S30, S37, S90, S108, S109

Note: See MHI Help File for full command documentation.

PROPRIETARY AT COMMAND SET

AUTO-MODE DETECTION

Type:

Configuration

Format:

AT [cmds] Nn [cmds]

Description:

Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed.

Command

Function

N0

Auto-mode detection disabled

í N1

Auto-mode detection enabled

COMMUNICATIONS MODE

Type:

Configuration

Format:

AT [cmds] &Mn [cmds]

Description:

Selects communications mode

Command

Mode

&M0

Asynchronous mode

CONFIGURATION PROFILES

Type:

Immediate

Format:

AT [cmds] &V [cmds]

Description:

Displays active and stored configuration profiles

Command

Function

&V0

Displays active and stored profile 0

&V1

Displays active and stored profile 1

DATA SET READY (DSR)

Type:

Configuration

Format:

AT [cmds] &Sn [cmds]

Description:

Selects DSR options

Command

Function

&S0

DSR forced high

&S1

DSR high only while modem is handshaking or connected

DATA TERMINAL READY (DTR)

Type:

Configuration

Format:

AT [cmds] &Dn [cmds]

Description:

Selects modem response to DTR

Command

Function

&D0

DTR override

&D1

DTR toggle causes online command mode

í &D2

Normal DTR operations

&D3

Resets on receipt of DTR

DIAL

Type:

Immediate

Format:

AT [cmds] D<#> [cmds]

Description:

Dials telephone number according to any modifiers included in the string

Note:

Any combination of modifiers can be used to produce the desired dial functions in sequence.

Command

Function

DP

Pulse dialing enabled

DR

Answer mode enabled; originate mode disabled following handshake initiation.

DS=n

Dial stored telephone number n

DT

Tone dialing enabled/Pulse dialing disabled

DW

Dialing resumed following dial tone detection

D,

Dialing paused for amount of time specified in S8 register

D@

Wait for Quiet Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by 5 seconds of silence

D!

Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook.

D;

Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command.

EXTENDED RESULT CODES

Type:

Configuration

Format:

AT [cmds] \Vn [cmds]

Description:

Selects extended result codes

Command

Function

\V0

Extended result codes disabled

\V1

Send extended response set 1

í \V2

Send extended response set 2

PULSE DIALING RATIO

Type:

Configuration

Format:

AT [cmds] &Pn [cmds]

Description:

Selects pulse dial make/break ratio

Command

Function

&P0

39/61ms at 10pps (North America)

&P1

33/67ms at 10pps (Europe)

REPORT INFORMATION

Type:

Immediate

Format:

AT [cmds] In [cmds]

Description:

Displays information requested

Command

Function

I0

Reports four digit product code

I1

Reports ROM checksum

I2

Reports internal memory test

I3

Reports device ID

I4

Reports internal ID

SPEAKER VOLUME

Type:

Configuration

Format:

AT [cmds] Ln [cmds]

Description:

Controls speaker volume

Command

Function

L0

Low volume setting

L1

Low volume setting

í L2

Medium volume setting

L3

Highest volume setting

TRELLIS CODING

Type:

Configuration

Format:

AT [cmds] &Un [cmds]

Description:

Enables/disables trellis coding

Command

Function

í&U0

V.32 trellis coding enabled

&U1

V.32 trellis coding disabled

EXTENDED AT COMMAND SET

AUTO-RETRAIN - AUTO-FALLBACK/FALL-FORWARD

Type:

Configuration

Format:

AT [cmds] %En [cmds]

Description:

Controls auto-retrain mode and fallback/fall-forward

Command

Function

%E0

V.22bis auto-retrain disabled

%E1

V.22bis auto-retrain enabled

 

COMPRESSION

Type:

Configuration

Format:

AT [cmds] %Cn [cmds]

Description:

Selects data compression

Command

Function

%C0

Data compression disabled

%C1

MNP5 enabled

CONNECT MODE

Type:

Configuration

Format:

AT [cmds] \Nn [cmds]

Description:

Controls the type of connection the modem will operate in

Command

Function

\N0

Normal mode enabled

\N1

Direct mode enabled

\N2

Reliable mode enabled

í \N3

Auto-reliable mode enabled

\N4

V.42 reliable mode enabled

FLOW CONTROL TYPE

Type:

Configuration

Format:

AT [cmds] \Qn [cmds]

Description:

Sets type of flow control used by modem

Command

Function

\Q0

Flow control disabled

\Q1

Bi-directional XON/XOFF flow control enabled

\Q2

CTS flow control by DCE enabled

\Q3

Bi-directional RTS/CTS flow control enabled

INACTIVITY TIMER

Type:

Configuration

Format:

AT [cmds] \Tn [cmds]

Range:

0-90

Unit:

1 second

Description:

Sets the length of time that the modem does not receive information before it disconnects.

V.42bis - MAXIMUM STRING LENGTH

Type:

Immediate

Format:

AT [cmds] "On [cmds]

Range:

6-250

Unit:

Characters

Description:

Selects string size for V.42bis compression