RAD DATA COMMUNICATIONS
ACE-20-T1
|
Card Type |
ATM Access Concentrator |
|
NIC Type |
T1, ISDN |
|
Chip Set |
Unidentified |
|
I/O Options |
AC power connector, DTE/DCE ports (2), alarm relay terminal block 9-pin serial port(2), T1 network interface via RJ-48 connectors (2) |
|
Wiring Type |
T1 |
|
T1 Transfer Protocol |
1.544Mbps |
|
Frame Type |
ESF, SF |
|
Frame Relay |
ATM PVC |
|
T1 Protocol |
AMI, B7ZS, B8ZS |
|
Data Bus |
External |
|
CONNECTIONS | |||
|
Function |
Label |
Function |
Label |
|
AC power connector |
CN1 |
Main T1 network port (RJ-48 connector) |
CN6 |
|
Alarm relay terminal block |
CN2 |
DTE serial port |
CN7 |
|
Sub T1 network port (RJ-48 connector) |
CN3 |
DCE serial port |
CN8 |
|
Channel 1 port (15-pin connector) |
CN4 |
Power switch |
SW2 |
|
Channel 2 port (25-pin connector) |
CN5 | ||
|
Note: Channel 1 and 2 data ports may have different interfaces than pictured above. Data port options include any combination of the following: 15-pin connector for X.21 interface, 25-pin connector for RS-530 interface, or 34-pin connector for V.35 interface | |||
|
USER CONFIGURABLE SETTINGS | |||
|
Setting |
Label |
Position | |
|
DCE timing enabled on port 1 |
JP1 |
Pins 2 & 3 closed | |
|
DTE timing enabled on port 1 |
JP1 |
Pins 1 & 2 closed | |
|
DCE timing enabled on port 2 |
JP2 |
Pins 2 & 3 closed | |
|
DTE timing enabled on port 2 |
JP2 |
Pins 1 & 2 closed | |
|
Signal ground is connected to the frame ground |
JP3 |
Pins 1 & 2 closed | |
|
Signal ground is not connected to the frame ground |
JP3 |
Pins 2 & 3 closed | |
|
Local software download enabled |
S1/1 |
On | |
|
Local software download disabled |
S1/1 |
Off | |
|
Data base initialization enabled |
S1/2 |
On | |
|
Data base initialization disabled |
S1/2 |
Off | |
|
Password enabled |
S1/3 |
On | |
|
Password disabled |
S1/3 |
Off | |
| » |
Factory configured - do not alter |
S1/4 |
Unidentified |
| » |
Factory configured - do not alter |
S1/5 |
Unidentified |
| » |
Factory configured - do not alter |
S1/6 |
Unidentified |
|
DIAGNOSTIC LEDS | |||
|
LED |
Color |
Status |
Condition |
|
RED 1 |
Unidentified |
On |
Device is detecting a red alarm condition on the main link |
|
RED 1 |
Unidentified |
Off |
Device is not detecting a red alarm condition on the main link |
|
YEL 1 |
Unidentified |
On |
Device is detecting a yellow alarm condition on the main link |
|
YEL 1 |
Unidentified |
Off |
Device is not detecting a yellow alarm condition on the main link |
|
RED 2 |
Unidentified |
On |
Device is detecting a red alarm condition on the sub link |
|
RED 2 |
Unidentified |
Off |
Device is not detecting a red alarm condition on the sub link |
|
YEL 2 |
Unidentified |
On |
Device is detecting a yellow alarm condition on the sub link |
|
YEL 2 |
Unidentified |
Off |
Device is not detecting a yellow alarm condition on the sub link |
|
TD1 |
Unidentified |
On |
Device is transmitting data on channel 1 |
|
TD1 |
Unidentified |
Off |
Device is not transmitting data on channel 1 |
|
RD1 |
Unidentified |
On |
Device is receiving data on channel 1 |
|
RD1 |
Unidentified |
Off |
Device is not receiving data on channel 1 |
|
TD2 |
Unidentified |
On |
Device is transmitting data on channel 2 |
|
TD2 |
Unidentified |
Off |
Device is not transmitting data on channel 2 |
|
RD2 |
Unidentified |
On |
Device is receiving data on channel 2 |
|
RD2 |
Unidentified |
Off |
Device is not receiving data on channel 2 |
|
ALRM |
Unidentified |
On |
Alarms are stored in alarm buffer |
|
ALRM |
Unidentified |
Off |
Alarms are not stored in alarm buffer |
|
TEST |
Unidentified |
On |
Device is conducting a loopback test |
|
TEST |
Unidentified |
Off |
Device is not conducting a loopback test |